Differences

This shows you the differences between two versions of the page.

--- 3dprinter:ender3s1 [2023/12/09 02:03] – [Cura and Klipper/Sonic Pad] Wuff
+++ 3dprinter:ender3s1 [2024/01/22 21:13] (current) – [S1/ S1 Pro parts] Wuff
@@ Line 75: / Line 75: @@
 https://www.thingiverse.com/thing:5531129/files
 About 1-2mm of overhang from the original connector needs to be removed to prevent the connector from catching the Z Axis motor.
+Hinge bed cable connector:
+https://www.thingiverse.com/thing:5953410
 Ender 3 S1 Flexible flat cable holder by Alei100
@@ Line 156: / Line 159: @@
 https://www.thingiverse.com/thing:5626066
-===== Sonic Pad =====
+====== Sonic Pad ======
 Enable root access:
@@ Line 217: / Line 220: @@
-==== Cura and Klipper/Sonic Pad ====
+===== Cura and Klipper/Sonic Pad =====
 https://www.creality.com/pages/download-creality-sonic-pad
@@ Line 241: / Line 244: @@
 https://www.creality.com/pages/download-creality-sonic-pad
+===== tuyaplug moonraker =====
+Requires "Moonraker Tuya Generic HTTP Service" as docker or on other system:
+https://github.com/teejo75/mtghs
+Add the configuration for the power plug to moonraker.conf
+<code - moonraker.conf>
+[secrets]
+#  Add as many sections as needed for the devices you want to control.
+[power tuyaplug]
+type: http
+#  In the below urls, <name> should be replaced with your device name per names.json, devices.json/snapshot.json
+#  <service> should be replaced with the hostname and port of the service.
+on_url: http://192.168.1.2:7126/on/3D-Printer
+off_url: http://192.168.1.2:7126/off/3D-Printer
+status_url: http://192.168.1.2:7126/status/3D-Printer
+request_template:
+    {% if command in ["on", "off"] %}
+        {% do http_request.set_method("PUT") %}
+        {% do http_request.add_header("api_key", "%s" % "ah2CTGhxONWEb76I1O5qZvM7yacCKmhf" ) %}
+        {% do http_request.set_body({}) %}
+    {% endif %}
+    {% do http_request.send() %}
+response_template:
+  {% set resp = http_request.last_response().json() %}
+  {resp["status"]}
+off_when_shutdown: False
+#   If set to True the device will be powered off when Klipper enters
+#   the "shutdown" state.  This option applies to all device types.
+#   The default is False.
+# off_when_shutdown_delay: 0
+#   If "off_when_shutdown" is set, this option specifies the amount of time
+#   (in seconds) to wait before turning the device off. Default is 0 seconds.
+on_when_job_queued: True
+#   If set to True the device will power on if a job is queued while the
+#   device is off.  This allows for an automated "upload, power on, and
+#   print" approach directly from the slicer, see the configuration example
+#   below for details. The default is False.
+locked_while_printing: True
+#   If True, locks the device so that the power cannot be changed while the
+#   printer is printing. This is useful to avert an accidental shutdown to
+#   the printer's power.  The default is False.
+restart_klipper_when_powered: True
+#   If set to True, Moonraker will schedule a "FIRMWARE_RESTART" to command
+#   after the device has been powered on. If it isn't possible to immediately
+#   schedule a firmware restart (ie: Klippy is disconnected), the restart
+#   will be postponed until Klippy reconnects and reports that startup is
+#   complete.  Prior to scheduling the restart command the power device will
+#   always check Klippy's state.  If Klippy reports that it is "ready", the
+#   FIRMWARE_RESTART will be aborted as unnecessary.
+#   The default is False.
+restart_delay: 8.
+#   If "restart_klipper_when_powered" is set, this option specifies the amount
+#   of time (in seconds) to delay the restart.  Default is 1 second.
+# This enables a power button in mainsail.
+bound_services: klipper
+</code>
+create a moonraker.secrets file containing the api/passwords. This doesn't appear to work properly though
+<code - moonraker.secrets>
+[mtghs]
+api_key: ah2CTGhxONWEb76I1O5qZvM7yacCKmhf
+</code>